Gas Plumbing Sydney

The most reliable sign is smell: gas suppliers add a distinctive rotten-egg odorant so leaks are detectable before concentrations reach dangerous levels. Beyond that, listen for a faint hissing sound near pipe joints, appliance connections or the meter. An unexplained spike in your quarterly gas bill can indicate a slow underground leak. If you have a garden and notice a patch of dead or yellowing vegetation above buried gas lines, that is worth investigating. If you spot any of these signs, do not touch electrical switches or open flames. Leave the property and call us on 02 8667 5354 from outside.

In NSW, anyone working on a gas fitting must hold a current gas fitting licence issued by NSW Fair Trading. Ask to see the licence card before work starts, and verify it at service.nsw.gov.au if you want certainty. Legitimate gas plumbers will also carry public liability insurance and, for certain appliance work, relevant manufacturer training. EKORP Plumbing’s licence is 322223C. We are also accredited with the Master Plumbers Association. Never allow anyone without a current gas fitting licence to work on your gas system: it is illegal and unsafe.

A licensed gas fitter should service your gas water heater annually. During the service, the technician will clean the burner assembly, check gas pressure at the appliance, inspect the thermocouple and safety controls, test for carbon monoxide at the flue outlet, and verify that all connections are sealed and sound. Annual maintenance keeps the unit running at peak efficiency, extends its service life, and catches developing faults before they become an emergency repair. If your unit is over eight years old, a service also gives you a realistic picture of how much life remains.

A complete gas water heater installation covers more than swapping the unit. We remove and dispose of the old system, position and secure the new unit according to manufacturer specifications, connect to the existing gas line with the correct fittings and flexible connectors, install or inspect the flue system, fit and test the temperature and pressure relief valve, pressure-test all gas connections before restoring supply, commission the unit and set the thermostat, and issue a compliance certificate confirming the installation meets AS/NZS 5601.1. You should receive written documentation from every licensed gas fitter at the end of a water heater installation.

Yes, this is one of the more common jobs we handle. We assess your hot water demand, recommend a suitably sized gas unit, run a new gas line to the location if no existing connection is present, install and commission the new system, and remove the old electric unit. Many households in St George and the Sutherland Shire find that gas hot water is cheaper to run over the long term, particularly with instantaneous units that only heat water on demand. We can provide a written quote covering the full scope before any work begins.

After connecting any gas appliance, we run through a set of mandatory safety checks before the job is considered done. We pressure-test all new connections for zero leakage, confirm gas delivery pressure at the appliance matches the manufacturer’s specification, check that all required clearances from combustible materials are met, verify correct ventilation or flue draw where the appliance is flued, test flame failure protection devices, check for carbon monoxide production during operation, and confirm that the isolation valve for the appliance is accessible and functional. These are not optional extras. They are part of every installation we complete.

Our target for emergency gas situations across St George and the Sutherland Shire is 60 minutes on site from the time you call. In practice, arrival time depends on where our nearest available plumber is and what is already in progress, so we give you a realistic estimate when you ring rather than a number we cannot back up. If you suspect a gas leak, do not wait indoors. Evacuate, avoid switches and open flames, and call us from outside on 02 8667 5354. After-hours rates apply for evening, weekend and public holiday call-outs, and we confirm those before dispatching.

Natural gas is delivered through the mains network, runs at relatively low pressure, and is lighter than air, so a leak disperses upward. LPG is heavier than air, which means it can pool at floor level and in low spaces, making ventilation design more critical. LPG is supplied in bottles or tanks and runs at higher pressure. The practical differences mean that appliances, regulators, injectors and fittings are not interchangeable between the two fuel types. If you are switching from one to the other, a licensed gas fitter needs to convert each appliance individually and re-certify the installation. We handle both systems and conversions between them.

Yes. Outdoor gas appliances are well within our scope. We install fixed gas lines to outdoor entertainment areas, fit gas bayonets for portable appliances, and hard-connect appliances like built-in BBQs, patio heaters and pool heating systems. Outdoor installations require weatherproof fittings and compliance with specific installation distances from structures, which our licensed gas fitters apply as standard. We can also service and repair existing outdoor gas appliances, including checking connections that may have deteriorated due to UV exposure or weather.

Modern gas hot water units, particularly continuous flow models, use significantly less energy than older storage systems because they do not maintain a large tank at temperature around the clock. That translates to lower gas bills over the life of the unit. Current models also have better safety controls, more reliable ignition systems and longer warranty periods than units made ten or fifteen years ago. If your existing gas water heater is approaching the end of its service life, upgrading proactively is almost always cheaper than dealing with a failure at short notice, which often means emergency rates and a wait for the right unit to arrive.